Contact Information:

MSc. in Materials Science and Engineering (Welding), Department of Materials Science and Engineering , Sharif University of Technology, 2006.

BSc. in Materials Science and Engineering (Industrial Metallurgy), Department of Materials Science and Engineering , Sharif University of Technology, 2004.

Journal Papers:

S. R. Mokabberi, M. Movahedi, A. H. Kokabi, "Effect of Interlayers on Softening of Aluminum Friction Stir Welds", Materials Science & Engineering A, 2018, Vol. 727, pp. 1–10.

M. Shamsian, M. Movahedi, A. H. Kokabi, A. Ozlati, "Upset-Resistance Welding of Aluminum to Copper Rods: Effect of Interface on Performance", Materials Science and Technology, Article in Press, 2018, DOI: 10.1080/02670836.2018.1482254. 

S. H. Arabi, M. Pouranvari & M. Movahedi, "Pathways to improve the austenite–ferrite phase balance during resistance spot welding of duplex stainless steels", Science and Technology of Welding and Joining, Article in Press, 2018, DOI: 10.1080/13621718.2018.1468949.

A. Hasanniah, M. Movahedi, "Welding of Al-Mg aluminum alloy to aluminum clad steel sheet using pulsed gas tungsten arc process", Journal of Manufacturing Processes, 2018, Vol. 31, pp. 494-501.

E. Fereiduni , M. Movahedi, A. Baghdadchi, “Ultrahigh-strength friction stir spot welds of aluminium alloy obtained by Fe3O4 nanoparticles”, Science and Technology of Welding and Joining, 2018, Vol. 23, No. 1, pp. 63–70.

S.H. Arabi, M. Pouranvari, M. Movahedi, “Welding metallurgy of duplex stainless steel during resistance spot welding”, Welding Journal, September 2017, Vol. 96,  pp. 307s-318s..

D. Shirmohammadi, M. Movahedi, M. Pouranvari, “Resistance spot welding of martensitic stainless steel: Effect of initial base metal microstructure on weld microstructure and mechanical performance”, Materials Science & Engineering A, 2017, Vol. 703, pp. 154-161.

M. Eftekhari, M. Movahedi, A.H. Kokabi, “Microstructure, Strength, and Wear Behavior Relationship in Al-Fe3O4 Nanocomposite Produced by Multi-pass Friction Stir Processing”, Journal of Materials Engineering and Performance, 2017, Vol. 26 (7), pp. 3516-3530.

E. Fereiduni, M. Movahedi, A.H. Kokabi, H. Najafi, “Effect of Dwell Time on Joint Interface Microstructure and Strength of Dissimilar Friction Stir Spot-Welded Al-5083 and St-12 Alloy Sheets”, Metallurgical and Materials Transaction A, 2017, Vol. 48A, pp. 1744-1758.

H. Karami Pabandi, M. Movahedi, A.H. Kokabi, “A new refill friction spot welding process for aluminum/polymer composite hybrid structures”, Composite Structures, 2017, Vol. 174, pp. 59-69.

S. Aliasghari, M. Ghorbani, P. Skeldon, H. Karami, M. Movahedi, “Effect of plasma electrolytic oxidation on joining of AA 5052 aluminium alloy to polypropylene using friction stir spot welding”, Surface & Coatings Technology, 2017, Vol. 313, pp. 274-281.

M. Tamizi, M. Pouranvari, M. Movahedi, "Welding metallurgy of martensitic advanced high strength steels during resistance spot welding", Science and Technology of Welding and Joining, 2017, Vol. 22 (4), pp. 327–335.

H. Karami Pabandi, M. Movahedi, A. Kokabi, Effect of tool rotational speed on friction spot joining of aluminum/polymer, Modares Mechanical Engineering, 2017, Vol. 17(1), pp. 431-440, (in Persian).

S. H. Arabi, M. Pouranvari, M. Movahedi, Influence of heat-input on mechanical behavior and phase balance of 2304 duplex stainless steel resistance spot welds, Modares Mechanical Engineering, 2017, Vol. 17(5), pp. 159-165 (in Persian).

A. Ozlati, M. Movahedi, H. Mohammadkamal, "Upset Resistance Welding of Carbon Steel to Austenitic Stainless Steel Narrow Rods", Journal of Materials Engineering and Performance, 2016, Vol. 25 (11), pp. 4902-4910.

H. Shahmiri, M. Movahedi, A. H. Kokabi, "Friction stir lap joining of aluminium alloy to polypropylene sheets", Science and Technology of Welding and Joining, 2016, Article in press, DOI: 10.1080/13621718.2016.1204171.

M.R. Arghavani, M. Movahedi, A.H. Kokabi, "Role of zinc layer in resistance spot welding of aluminium to steel", Materials and Design, 2016, Vol. 102, pp. 106-114.

E. Fereiduni, M. Movahedi, A.H. Kokabi, "Aluminum/steel joints made by an alternative friction stir spotwelding process", Journal of Materials Processing Technology, 2015, Vol. 224, pp.1–10.

M Sarkari Khorrami, M. Movahedi, "Microstructure evolutions and mechanical properties of tubular aluminum produced by friction stir back extrusion", Materials and Design, 2015, Vol. 65, pp.74–79.

M. Sarkari Khorrami, S.Samadi, Z.Janghorban, M.Movahedi, "In-situ aluminum matrix composite produced by friction stir processing using Fe particles", Materials Science & Engineering A, 2015, Vol. 641, pp. 380–390.

M. Sarkari Khorrami, A. H. Kokabi,  M. Movahedi, "Study on Joint Interface and Mechanical Properties of Cu/Pb-Sn/Cu Lap Joint Produced by Friction StirSoldering Process", Journal of Materials Engineering and Performance, 2015, Vol. 24, pp. 2158-2169.

M. Movahedi, A.H. Kokabi, S.M. Seyed Reihani, H. Najafi, S.A. Farzadfar, W.J. Cheng, C.J. Wang, "Growth kinetics of Al–Fe intermetallic compounds
during annealing treatment of friction stir lap welds", Materials Characterization, 2 0 1 4, Vol. 9 0, pp. 1 2 1 – 1 2 6.

M. Movahedi, A. H. Kokabi and S. M. Seyed Reihani, W.J. Cheng and C.J. Wang, "Effect of annealing treatment on joint strength of aluminum/steel friction
stir lap weld", Materials and Design, 2013, Vol. 44, pp. 487-492.

M. Movahedi, A. H. Kokabi and S. M. Seyed Reihani, “Investigation on friction stir lap welding of aluminium to aluminium clad steel sheets”, Science and Technology of Welding and Joining, 2012, Vol. 17, No. 3, pp. 231-236.

M. Movahedi, A. H. Kokabi, S. M. Seyed Reihani and H. Najafi, “Effect of tool travel and rotation speeds on weld zone defects and joint strength of aluminium steel lap joints made by friction stir welding”, Science and Technology of Welding and Joining, 2012 Vol. 17, No. 2, pp. 162-167.

M. Movahedi, A.H. Kokabi, H.R. Madaah-Hosseini and M. Kiani, “Roll bonding behaviour of Al-3003/Al-4043 and Al-3003/Zn sheets”, Metals and Materials International, 2011, Vol. 17, No. 4, pp. 665-670.

M. Movahedi, A.H. Kokabi and S.M. Seyed Reihani, “Investigation on the bond strength of Al-1100/St-12 roll bonded sheets, optimization and characterization”, Materials and Design, 2011, Vol. 32,  pp. 3143–3149.

M. Movahedi, A.H. Kokabi and H.R. Madaah-Hosseini, "An investigation on the soldering of Al 3003/Zn sheets", Materials Characterization, 2009, Vol. 60, Issue 5, pp. 441-446.

M. Movahedi, H.R. Madaah-Hosseini and A.H. Kokabi, "The influence of roll bonding parameters on the bond strength of Al-3003/Zn soldering sheets", Materials Science and Engineering A, 2008, Vol. 487, pp. 417–423.

M. Movahedi, A. Karimi Taheri and H. Niamanesh, "Combined effect of cooling slope angle and mould vibration on semisolid microstructures of wrought aluminium alloy 7075", International Journal of Cast Metals Research, 2007, Vol. 20, No. 4, pp. 221-227.

Karimi Taheri, M. Movahedi and H. Niamanesh, "The effect of mold vibration on the microstructure of Al7075 thixoforming billet produced by the cooling slope thechnique", Sahrif Journal of Science and Technology, Autumn 2007, No. 39, pp. 53-59 (in Persian).

M. Movahedi and A.H. Kokabi, "An investigation on the roll bonding strength and bending resistance of the Al3003/Zn soldering sheets", Metallurgical Engineering, Spring 2007, No. 26, Vol. 10, pp. 12-17 (in Persian).

A. Mohassel, A.H. Kokabi, P. Davami, E. Ranjbarnodeh and M. Movahedi,  "Heat transfer modelling in wide gap rail thermite welding",  Journal of Advanced Materials and Processing, 2012, No. 2, Vol. 1, pp. 29-37.

E. Fereiduni, M. Movahedi, A.H. Kokabi, "Effect of Intermetallic Compounds on the Strength of Dissimilar Friction Stir Spot Welded Al/Steel Joints", Journal of Materials and Metallurgical Engineering, Accepted manuscript (in Persian).

E. Fereiduni, M. Movahedi, A.H. Kokabi, "Effect of welding parameters on dissimilar friction stir spot welded Al-5083/St-12 alloy sheets", Journal of Materials and Metallurgical Engineering, Accepted manuscript (in Persian).

Conference Papers:

M. Farshbaf Ahmadi Pour, M. Movahedi, A.H. Kokabi, S. Ahmadian, “Effect of Heat Input on Mechanical Behavior of Al-1050/TiO2-Graphite Nano-Composite Produced by Friction Stir Processing”, 5^th International Conference and 10^th Congress of Iranian Metallurgical & Materials Engineering Society & Iranian Foundrymen’ Society, 2016 (in Persian).

A. Baghdadchi, M. Movahedi, E. Fereiduni, “Effect of addition of Fe3O4 nano-powders in friction stir spot welding of aluminum 5083 sheets”, 5^th International Conference and 10^th Congress of Iranian Metallurgical & Materials Engineering Society & Iranian Foundrymen’ Society, 2016 (in Persian).

M. Farshbaf Ahmadi Pour, M. Movahedi, A. H. Kokabi, "Al-1050/TiO₂-Graphite Nano-Composite Produced by Friction Stir Processing", 6^th International Conference on Nanostructures (ICNS6), 2016.

E. Fereiduni, M. Movahedi, A.H. Kokabi, "Effect of Tool Positioning on the Strength of Dissimilar Friction Stir Spot Welded Al/Steel Joints", 4^th International Conference and 9^th Congress of Iranian Metallurgical & Materials Engineering Society & Iranian Foundrymen’ Society, 2015 (in Persian).

A. Najafi, M. Movahedi, A. Sadoughi, "Effect of reinforcement percent and tool rotating direction on microstructure and mechanical properties of Al-1050/Fe produced by friction stir processing", 4^th International Conference and 9^th Congress of Iranian Metallurgical & Materials Engineering Society & Iranian Foundrymen’ Society, 2015 (in Persian). 

M. Movahedi, A.H. Kokabi, S.M. Seyed Reihani and H. Najafi, “Mechanical and Microstructural Characterization of Al-5083/St-12 lap joints made by friction stir welding”, Procedia Engineering (ICM-11), 2011, Vol. 10, pp. 3297–3303. 

M. Movahedi, V. Firouzdor, B. Nemati and A. H. Kokabi, "Resistance spot welding of Al5005 aluminum alloy", Proceedings of The First South-East Asia International Institute of Welding Congress, Bangkok, Thailand, November 2006, pp. 151-156.

M. Movahedi, A. Karimi Taheri and H. Niamanesh, "Effect of cooling slope angle on semisolid microstructures of wrought alloy Al7075", 10th National Conference of Iranian Metallurgical Engineers Society, Mashhad, October, 2006, p. 22, (in Persian).

M. Movahedi and A.H. Kokabi, "An investigation on the roll bonding strength and bending resistance of the Al3003/Zn soldering sheets", 10th National Conference of Iranian Metallurgical Engineers Society, Mashhad, October, 2006, p. 100, (in Persian).

Ε. Νejati, V. Firouzdor, M. Movahedi and F. Khomamizadeh, "An investigation on the effect of the deep cryogenic treatment on thermal fatigue behavior of A380 aluminum alloy", 10th National Conference of Iranian Metallurgical Engineers Society, Mashhad, October, 2006, p. 133, (in Persian).

M. Movahedi, A. H. Kokabi and H.R. Maddah Hosseini, "Soldering of Al3003 Alloy by Using Al3003/Zn Soldering Sheets", 11th National Conference of Iranian Metallurgical Engineers Society, Isfahan, October, 2007 (in Persian).